- Can I daisy chain recessed lights?
- Can you have too many recessed lights?
- Why is recessed lighting bad?
- Can I wire lights and outlets on the same circuit?
- Can I use 14 gauge wire on a 20 amp breaker?
- How many LED can lights do I need?
- How many outlets and lights can be on a 15 amp circuit?
- Does it matter what wire goes where on a light switch?
- How many lumens is a 30×40 shop?
- How many outlets can you put on one circuit?
- How many recessed lights is too many?
- How do you wire multiple lights to one switch?
- Should recessed lighting be symmetrical?
- What happens if you wire a light switch wrong?
- Is 3000 lumens too bright?
- How far apart do you put LED downlights?
- Is it OK to mix 12 and 14 gauge wire?
- How many can lights can be on one switch?
Can I daisy chain recessed lights?
Remember that you must run one ultra-thin extension cable (or run of low voltage wire) for each light.
You can not daisy chain multiple lights together.
Run your electrical wire from the switch/dimmer location to each driver..
Can you have too many recessed lights?
It often seems that installing recessed lights is a cure all, but they cannot properly wash light upon walls and all dark corners, which would bounce reflective light into the room. In fact, using too many recessed light may leave areas of your room dark and may even cost you more on your electric bill.
Why is recessed lighting bad?
You’ve probably heard that recessed lights can be dangerous and energy-wasting because they can’t be covered with insulation (without creating a fire risk) and because they leak air into the attic. This is true, but it applies only to standard (usually cheapo) fixtures.
Can I wire lights and outlets on the same circuit?
Basic answer to your question of can a mixture of lights and receptacles be installed on a single circuit is yes. … In your case it is okay to install a receptacle alongside the switch. However you need a neutral as well as a hot wire which you may not have. Test to see if you have a neutral with a test light or meter.
Can I use 14 gauge wire on a 20 amp breaker?
NEC 240.4(D)(3) states that 14 AWG must be protected at 15A. You can not use 14 AWG anywhere on a circuit that has a 20A breaker. If you are putting 15 amp receptacles on a 20 amp circuit with 12 gauge wire, then you MUST use the screw terminals, not the back stab terminals. … Just use the side terminals.
How many LED can lights do I need?
Measure your room to see how many fixtures you will need. A common rule of thumb is that you use one recessed light for every 4 to 6 square feet of ceiling space. Doing so provides even, overall illumination.
How many outlets and lights can be on a 15 amp circuit?
10 outletsGenerally, homes have eight to 10 outlets on a 15 amp breaker but not all are used at the same time. Lights and outlets are normally wired on separate branch circuits, which means that the lights will be protected by a separate circuit breaker to the one which protects the outlets.
Does it matter what wire goes where on a light switch?
If your switch has a “LINE” marking, the always hot wire goes to this. The other connection will be “LOAD” where the load (ie light fixture) is wired. The load wire may have red electrical tape on it to differentiate.
How many lumens is a 30×40 shop?
I’ve done some research and from the formulas I’ve seen, for a 30×40 shop to have 100 lumens per sq/ft (optimum)….
How many outlets can you put on one circuit?
One rule of thumb is to assign a maximum draw of 1.5 amps to each receptacle, which allows for 10 receptacles on a 20-amp circuit.
How many recessed lights is too many?
don’t have more than 3-4 feet space between them. From your layout, it looks you are okay. You will never have too many.
How do you wire multiple lights to one switch?
You can do this light switch wiring in one of two ways. The most common is to daisy-chain the light fixtures by connecting them to each other and hooking the first one up to the switch. The other way to wire multiple lights to one switch is to connect all of them directly to the switch in a “home run” configuration.
Should recessed lighting be symmetrical?
The General Lighting Layout The recessed lights should be aligned and equally spaced across the ceiling. Resist the temptation to place the lights according to objects in the room (such as furniture).
What happens if you wire a light switch wrong?
You could put the switch on the neutral wire and everything would work, but it would leave voltage potential to ground in the light when it is switched off. That makes it a bit hazardous for changing light bulbs. If you became an electrical path to ground through a wet floor or something you could get a shock.
Is 3000 lumens too bright?
A foot-candle is a measure of how bright the light will be when you are a foot away from the light source. … 30-40 foot candles are around 3,000-4,000 lumens. In other words, 3,000 lumens is meant to give a room a brighter light. This is not ideal if you have a small room and it’s a bedroom.
How far apart do you put LED downlights?
Then space your downlights evenly across the room for a balanced look. As a rule of thumb, we suggest you divide your ceiling height by 2 to give you the space required between each downlight. For example if your ceiling is 8 foot high, then position your lights 4 feet apart.
Is it OK to mix 12 and 14 gauge wire?
Anyway, the first subject is a bit touchy because it makes it difficult to perform an inspection when all of the wires coming into the panel are 12 but many of the circuits have 14 in them too. There is nothing against code mixing wire size for these circuits as long as the OCPD matches the smallest wire.
How many can lights can be on one switch?
The main limitation to the number of recessed fixtures you can run at the same time is the rating of the circuit breaker that controls the circuit. Each fixture with a 60-watt incandescent or halogen bulb draws about 1/2 amp, so a 15-amp breaker for a standard lighting circuit would be able to handle 30 of them.